IEC 61058-1 PDF

IEC Standard | Switches for appliances – Part Requirements for mechanical switches. This part of IEC applies to switches for appliances. The switches are intended to control electrical appliances and other equipment for. This part of IEC applies to electronic switching devices and shall be used in conjunction with the general requirements of IEC

Author: Mooguzahn Moogusida
Country: Azerbaijan
Language: English (Spanish)
Genre: Spiritual
Published (Last): 9 September 2004
Pages: 244
PDF File Size: 6.51 Mb
ePub File Size: 6.41 Mb
ISBN: 770-3-12096-573-2
Downloads: 81464
Price: Free* [*Free Regsitration Required]
Uploader: Zolojin

IEC 61058-1

At the beginning of the test, the windings shall be at ambient temperature. If a decorative cover is backed by an inner cover, fracture of the decorative cover is ief if the inner cover withstands the test after removal of the decorative cover These may be special specimens with the appropriate components omitted.

I37 Annex F informative Switch application guide For the purpose of testing for certification, standard test circuit conditions have been established which are representative of typical circuits in the application.

A steel ball of 5 mm diameter is pressed against the surface of the specimen by a force of 20 N. Standards Subsctiption may be the perfect solution.

BS EN IEC 61058-1:2018

However, the contacts of any incorporated automatic protective device shall not be welded, unless the switch is obviously useless Alexa Actionable Analytics for the Web. Overview of immunity tests.

  AL FIQH AL ISLAMI WA ADILLATUHU PDF

The declared full travel of the actuating member if any shall be applied during these tests. Compliance is checked by inspection and during the tests of 19,2.

If jec temperature is limited by a fuse, the following additional test is carried out: Radiated, radio-frequency, electromagnetic field immunity test 7 Amendment 1 lEC The load conditions are as follows: For terminals for the connection of supply cables or cords, the conductor shall have the largest cross-sectional area specified Screws and nuts are tightened and loosened by means of a suitable test screwdriver or spanner, the torque applied when tightening being equal to that specified in the appropriate column of table 20, if not otherwise specified.

Please download Chrome or Firefox or view our browser tips. It shall still be possible to actuate the actuating member to provide the appropriate 16058-1. During the measurements, each one of the resistors and all other components, if any. Insulating linings, barriers and the like shall not have worked loose. Path under consideration includes a-parallel- or converging-sided groove of any deptii with a widtii less than “X” mm.

I’d like to read this book on Kindle Don’t have a Kindle? For the purpose of this test for switches classified according to 7.

BS EN IEC – Switches for appliances. General requirements (British Standard)

Your basket is empty. In general, compliance is checked by carrying Out all the relevant tests. Alternatively, the temperature rise of the switch may be measured on specially prepared specimens: Resistive current, peak surge current, voltage and nature of supply may be indicated accordingly as follows: The results of the tests for switches with indicator lamps shall be considered to apply to switches of equivalent construction without indicator lamps, or to indicator lamps of equivalent construction without he switching mechanism, 5.

  GUY RACHET TRAGEDIA GREACA PDF

Th’e electrical ratings of the switch are then oec using the standard circuit conditions.

SXmm Example 2 Condition: After the test, the electronic switch shall be in the original ieec and’ the setting shall be unchanged. Immunity to conducted disturbances, induced by radio-frequency fields Protection of persons and equipment by enclosures — Probes for verification Switches for appliances — Part Compliance is ciiecked by inspection and by ttie tests in This part of IEC does not apply to devices covered by: For multi-circuit switches the operating sequence of the pairs of contacts shall be declared if this is of importance for the safety of the user.

Please first log in with a verified email before subscribing to alerts.