GEFRAN 600 MANUAL PDF

Buy Gefran PID Temperature Controller, 48 x 48 (1/16 DIN)mm, 2 Output Relay, Gefran. Main Product. Technical Reference. User’s manual GEFRAN Buy Gefran PID Temperature Controller, 48 x 48 (1/16 DIN)mm, 2 Output Logic, Gefran series of Microprocessor Controllers support thermocouple. CONTROLLER USER’S MANUAL SOFTWARE VERSION x code L / Edition 15 – 07/ 1 • INSTALLATION Display Keys Accuracy • Dimensions.

Author: Akinoshakar Yozshum
Country: Martinique
Language: English (Spanish)
Genre: Technology
Published (Last): 2 January 2005
Pages: 284
PDF File Size: 12.89 Mb
ePub File Size: 18.64 Mb
ISBN: 754-6-57899-177-2
Downloads: 52060
Price: Free* [*Free Regsitration Required]
Uploader: Tojara

The instrument can have up to 4 outputs: Repairs must be done only by trained and specialized personnel. Der 24 V-Eingang ist isoliert bis V.

F If possible, to optimize parameters, change the setpoint and check temporary response. In addition to control and alarm outputs, you can have outputs gefrran repeat the state of the digital or retransmission input by process variable, setpoint, drift, alarm limits and values acquired from serial line.

The HB alarm can be activated only with ON times greater than 0. If the Integral Tefran value is too long Weak integral actiondeviation between the controlled variable and the setpoint may persist.

It is useful for calculation of PID parameters when the system is around the set-point. By pressing ‘print’ button you will print only current page. In this casethe Stu code is not cancelled. You can display the load current by selecting the item In. Cooling PID parameters are therefore calculated based on heating parameters according to the specified ratio. A single switch can control several units.

  FABIOLA CARDINAL WISEMAN PDF

Repairs must be done only by trained and specialized personnel. The direct HB alarm trips when the ammeter input value is below the limit set for Hb.

EMC conformity has been tested with the following manula. How to switch the unit ON: Repairs must be done only by trained and specialized personnel. Page 28 The board is automatically recognized by the instrument, which enables display and setting of the parameters involved. Displays PV value, optional exclusion. When calculations are finished, the system disables automatically and the control proceeds until the setpoint is reached.

S or at maximum calibration value Max. Page 7 Minimum limit auxiliary l5.

The instrument can also select display parameters based on hardware configuration, automatically masking irrelevant parameters. It can be one of two types: MEd 0 Air 1 Oil 2 Water c.

The does all the rest. This provides a very low secondary current, suitable for an electronic measurement circuit.

Gefran 600 User Manual

The function of each output is freely configurable from the faceplate keys. If the response is too slow, reduce it.

If Inc, Dec, F keys are not pressed within 15 sec, display returns automatically to P. Use a cloth dampened in. The board is automatically recognized by the instrument, which enables display and setting of the parameters involved.

Sie eignet sich zur Steuerung von Wechselstromlasten bis maximal V a. It can signal variations in load input by identifying the current value in ammeter input in the range The variable for example, temperature must be that assumed at zero power room temperature. Resistors must be at least 2W ; fit a 1N diode in parallel with the coil of inductive loads that operate in DC.

  DADO UNI 5587 PDF

Cencal Memory Map – Resolution 7 bit PWM. Theboard is automatically recognized by the instrument, which enables display and setting of the parameters involved. It has 4 keys, two green LED displays, each with 4 digits, 4 red signal LED’s for the 4 logic or relay outputs, and 3 other programmable LED’s to signal the various operational states of the instrument. Guide Modbus A PC programming kit is available for even simpler configuration, composed of a cable and a guided program for Windows environment see data sheet code Documentation – Previous versions.

To mount two or more units side by side, respect the cut-out dimensions shown in the drawing. PID parameters are calculated by measuring overshoot and the time needed to reach peak.

Configurable Controller – Gefran

It is placed near the power supply circuit and near high-voltage relay contacts. Provides a complete operator interface protected by a Lexan membrane that ensures level IP65 faceplate protection. Description Universal input configurable from faceplate Accuracy better than 0. To fix the unit, insert the brackets provided into the seats on either side of the.

Don’t have an account?