ASTM D5961 PDF

Procedure A in ASTM D , has the objective to test composite laminates double-edged. The pin in the device, creating two cutting plans, extracts a segment. ASTM D TESTING FIXTURE – PROCEDURE B. FASTENER BEARING SPECIMEN SUPPORT. Pdf icon button Download PDF. The bearing strength of a . Model No. ASTM.D – Double Shear Fastener Test Fixture. The Double Shear Fixture applies a double shear load via two loading plates secured to the.

Author: Goll Fegami
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Automotive
Published (Last): 6 October 2006
Pages: 179
PDF File Size: 14.21 Mb
ePub File Size: 14.38 Mb
ISBN: 199-4-24841-322-5
Downloads: 7600
Price: Free* [*Free Regsitration Required]
Uploader: Net

ASTM D Polymer Matrix Composite Laminate Bearing Strength Test Equipment

The aztm of acceptable test laminates and thicknesses are described in 8. Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.

Obviously, a piece of the same test material can be used as a spacer, if desired. Active aastm current version of standard. The properties obtained from this testing standard are the ultimate bearing strength, the offset bearing strength and the stress-strain curve.

The test fixture is shown in Fig. Wyoming Test Fixtures Inc. Sources of Additional Information: By means of our plastic testing expertise and modular product design, we will help find the testing solution that is right for you. Within the text the inch-pound units are shown in brackets. This simple test fixture is shown in Fig.

While this test method may be referenced as guidance in bearing bypass test programs, the scope of this test method is limited to bearing failure modes.

Link to Active This link will always route to the current Active version of the standard. We are confident that we have what you are looking for. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

Standard specimen configurations using fixed values of test parameters are described for each procedure. For protruding head fasteners, Procedure D will typically yield somewhat higher results than Procedure C d596 to both stress peaking and finite edge distance in Procedure Cand Procedures A and C yield roughly equivalent results. The other three procedures are pin bearing fixtures, as will be described here. Combining values from the two systems may result in non-conformance with the standard.

  CITY OF SPLENDORS WATERDEEP PDF

The two lower components of the fixture are spread apart to permit inserting the 1.

The maximum force attained and the deformation of the hole in the specimen are recorded. Procedure D of ASTM D loads the laminate bearing specimen in double shear through a close-tolerance, lightly torqued fastener or pin. As described in Section H-2, the SACMA fixture is much easier to use since the specimen holder is one piece, with adjustable bushings to accommodate variations in specimen thickness.

Link to Active This link will always route to the current Active version of the standard. The composite material forms are limited to continuous-fiber or discontinuous-fiber tape or fabric, or both reinforced composites for which the laminate is balanced and symmetric with respect to the test direction.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Testing Procedure The test methods are as follows. The flat tang at the top of the test fixture is gripped in a wedge grip and a tensile force is applied to the lower end of the specimen. Sometimes the customer has a requirement to test non-standard specimen sizes, requiring Wyoming Test Fixtures, Inc. These Procedure B and C configurations have been extensively used in the development of design allowables data.

That is, a single shear plane is developed in the loading pin as the tensile load is applied. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.

An alternate version of the test fixture shown in Figs.

ASTM D 5961 TESTING FIXTURE – PROCEDURE B

The Procedure C specimen is particularly well-suited for development of countersunk-fastener bearing strength data where a near-double-shear fastener rotational stiffness is desired. Each half of the fixture is 0. However, when fully documented in the test report, a number of test parameters may be optionally varied.

  AR15COM AMMO ORACLE PDF

Standard specimen configurations using fixed values of test parameters are described for each procedure.

ASTM D5961 Double Shear Fixture for Bearing Composite Laminate | GD5961-A

A tensile load is applied until a maximum loading has been reached, monitoring both applied force and hole deformation, as described in the ASTM standard. Sources of Additional Information:. Give one of our application engineers a call today for help with creating the best budget and testing plan according to ASTM D Historical Version s – view previous versions of standard. Note that the scope of this test method is limited to bearing and fastener failure modes. The composite material forms are limited to continuous-fiber or discontinuous-fiber tape or fabric, or both reinforced composites for which the laminate is balanced and symmetric with respect to the test direction.

However, when fully documented in the test report, a number of test parameters may be optionally varied.

Have a question about conducting the test for this standard? Properties, in the test direction, which may be obtained from this test method include the following: Procedure B is actually a specimen support fixture and is described in Section H-1 of this product catalog.

ASTM D Double Shear Fixture for Bearing Composite Laminate | GDA

The values stated in each system may not be exact d961 therefore, each system shall be used independently of the other. The standard configuration for each procedure is very specific and is intended primarily for development of quantitative double- and single-shear bearing response data for material comparison and structural design.

A pin or fastener is inserted in the hole, the fastener being torqued as desired. The specimen is placed on the right surface of the test fixture, aligning the hole in the end of the specimen with the hole shown in the fixture and a fastener inserted and lightly torqued.