The salt spray (or salt fog) test is a standardized and popular corrosion test method, used to ASTM B was the first internationally recognized salt spray standard, originally published in Other important relevant standards are. Designation: B – 07a Standard Practice for Operating Salt Spray (Fog) Apparatus1 This standard is issued under the?xed designation B. ASTM B Testing, also known as a Standard Practice for Operating Salt ASTM B Testing requires controls over many operational parameters such as: .

Author: Mazurr Jubar
Country: Netherlands
Language: English (Spanish)
Genre: Health and Food
Published (Last): 22 September 2016
Pages: 473
PDF File Size: 11.67 Mb
ePub File Size: 4.52 Mb
ISBN: 864-3-68144-304-6
Downloads: 80762
Price: Free* [*Free Regsitration Required]
Uploader: Tam

Test specimens are placed in an enclosed chamber, and exposed to a changing aetm that comprises the following 2 part repeating cycle. ASTM B was the first internationally recognized salt spray standard, originally published in This is followed by 0. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

The conditions of making the scratch shall be as de? The major features of a walk-in type cabinet, which differs signi? Originally approved in The zinc carbonates are not produced when a hot-dip galvanized specimen is exposed to a salt spray fog, therefore this testing method does not give an accurate measurement of corrosion protection.

The first prerequisite for your test chamber to operate properly is that it is regularly serviced and well maintained. NOTE 7—If the tower is run outside of these suggested temperature and pressure ranges to acheive proper collection rates as described in The most commonly used type is made of plastic.

Painted surfaces with an underlying hot-dip galvanized coating can be tested according b117-07aa this method. The chamber has the following features: Nozzles are not necessarily located at one end, but may be placed in the center and can also be directed vertically up through a suitable tower.

Salt spray test

The most appropriate test cycle and spray solutions are to be agreed between parties. Zstm Blocks for Evaporators. This acceleration arises through the use of chemically altered salt spray solutions, often combined with other test climates and in most cases, the relatively rapid cycling of these test climates over asm.


This formula yields a result of 53 g 1. Preparation of Test Specimens 6. The salt spray or salt fog test is a standardized and popular corrosion test method, used to check corrosion resistance of materials and surface coatings. Although popular in certain industries, modified salt spray testing has in many cases been superseded by Cyclic corrosion testing CCT The type of environmental test chambers used for modified salt spray testing to ASTM G85 are generally similar to the chambers used for testing to ASTM Bbut will often have some additional adtm, such as an automatic climate cycling control system.

Vent piping should be of sufficient size asym that a minimum of back pressure exists and should be installed so that no solution is trapped.

SaliCORR® ASTM B Sodium Chloride

The cleaning method shall be optional depending b117-07z the nature of the surface and the contaminants. Mix mL of hydrochloric acid sp gr 1. NOTE 4—The freshly prepared salt solution may be?

Halides Bromide, Fluoride, and Iodide other than Chloride shall constitute less than 0. The longer the accelerated corrosion test, the longer the process remains out of control, and larger is the loss in the form of non-conforming batches.

salt spray test, ASTM B, corrosion tests

How can I check whether my salt spray test chamber operates properly? The recorded temperature must be obtained with the salt spray chamber closed to avoid a false low reading because of wet-bulb effect when the chamber is open. When b1117-07a a speci? Test solution tank L. Nozzles calibrated for air consumption and solution-atomized are available. Most commonly, the time taken for oxides to appear on the samples under test is compared to expectations, to determine whether the test is passed or failed.


A asgm arrangement is shown in Fig. This may be accomplished by placing the apparatus asym a constant-temperature room, but may also be achieved by surrounding the basic chamber of a jacket containing water or air at a controlled temperature. The operating characteristics of a typical nozzle are given in Table X1. Variability has been observed when zstm specimens are tested in satm fog chambers even though the testing conditions are nominally similar and within the ranges speci?

The appearance of corrosion products rust or other oxides is evaluated after a pre-determined period of time. However, these testing standards neither provide information of testing periods for the coatings to be evaluated, nor the appearance of corrosion products in form of salts. Chamber volumes vary from supplier to supplier. No, VLM has own development and production facilities for corrosion testing equipment.

This produces a corrosive environment of dense salt water fog also referred to as a mist or spray in the chamber, so that test samples exposed to this environment are subjected to severely corrosive conditions. Options for corrosion chambers. The company was founded in and from the very beginning it started working aastm innovative design concepts for test chambers.

Options for corrosion chambers. Cyclic corrosion testing is better suited to this. Failure to meet this requirement implies instability in the chemical process of the pre-treatment, or the paint quality, which must be addressed immediately, so that the upcoming batches are of the desired quality.

Records and Reports In contrast to the full plastic construction, the VLM test rooms consist of a combination of recyclable plastics and metal e. This standard has been approved for use by agencies of the Department of Defense.