ASTM A – / ASTM A – for Austenitic Cast Iron provided by Dandong Foundry in China. This is an America standard for the physical properties. Ni-Resist Iron has an austenitic matrix with about 10% alloy carbides. It is suitable for corrosive environments in sour well oils, salts, salt water acids. See the chemical composition and physical properties of ASTM A Grade 1, find alternative materials, and connect with suppliers.
|Published (Last):||9 December 2010|
|PDF File Size:||18.61 Mb|
|ePub File Size:||1.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
The castings shall be free of injurious defects.
Test Methods E 30 should only be a46 for analyzing those elements for which speci? If castings are to be heat treated, test bars shall be included in the same furnace load. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxashm service astm.
Except as otherwise speci? Waiving of Inspection by Agreement Number of Test In other respects, the castings shall conform to a4366 points may be speci? Originally published as A —59 T. The types of castings covered here are: It shall be an open mold made of suitable core sand with a minimum of 11? The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
ASTM A436 Grade 1
The materials shall be manufactured by melting in any furnace that produces castings which includes cupolas, air furnaces, electric furnaces, crucible furnaces, and so forth. Otherwise, the austenite that is supersaturated with respect to carbon may reject carbon during service and produce dimensional changes. Types 1b, 2b, 3, and 5 may be attracted to a magnet.
NOTE 1—Alnico magnets should not be used. This specification covers austenitic gray iron castings that are used primarily for their resistance to heat, corrosion, and wear. This standard has been approved for use by agencies of the Department of Defense. Materials and Manufacture 4.
ASTM A436 Grade 6
Magnetic Property Requirements 7. Workmanship, Finish, and Appearance 9. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
Link to Active This link will always route to the current Active version of the standard. In these cases, either of the test specimens shown in Fig. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This nonmagnetic test is a convenient qualitative test only for Types 1, 2, and 4 and shall not be used as a basis for acceptance. Heat and product analyses shall be performed wherein specimens shall conform to required chemical composition of carbon, silicon, manganese, nickel, copper, chromium, sulfur, and molybdenum. Tension Test Specimens Preparation for Delivery The six types shall conform to the requirements given in Table 2.
Drillings are not reliable because of the probable loss of graphite. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The test bars shall be cast in open molds made of suitable core sand with a minimum of 11?
The location and orientation of such tension test specimens cut from castings shall be speci?
ASTM A – 84() Standard Specification for Austenitic Gray Iron Castings
Austenitic gray iron is characterized by uniformly distributed graphite flakes, some carbides, and the presence of sufficient alloy content to produce an austenitic structure. If any tension test specimen shows obvious defects, another may be cut from the same test bar a463 from another test bar representing the same metal.
Tension tests shall be performed wherein specimens shall conform to required tensile strength and Brinell hardness. Last previous edition A — The materials shall undergo a nonmagnetic test which is based on the material’s attraction to a small steel horseshoe-type magnet and a magnetic permeability test in the event that nonmagnetic castings are specified.
Austenitic gray iron is characterized by uniformly distributed graphite? Historical Version s – view previous versions of standard. Responsibility for Inspection A — 84 Reapproved Standard Speci? A superscript epsilon e indicates an editorial change since the last revision or reapproval.
In case no option is expressed, the manufacturer shall make the choice. A number in parentheses indicates the year of last reapproval. In the event that nonmagnetic castings are speci? Referenced Documents purchase separately The documents listed below are referenced within a43 subject standard but are not provided as part of the standard.
ASTM A – / ASTM A – for Austenitic Cast Iron
ASTM D e1. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown asrm. These include cupolas, air furnaces, electric furnaces, crucible furnaces, and so forth. The size of bar cast to represent the casting shall be at the option of the purchaser. This abstract is a brief summary of the referenced standard. The reduced section shall have a gradual taper from the ends toward the center, with the ends 4a36.
Packing and marking shall also be adequate to ensure acceptance and safe delivery by the carrier for a43 mode of transportation employed. Where some machining is required, the 3.