ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
|Published (Last):||10 July 2006|
|PDF File Size:||7.58 Mb|
|ePub File Size:||5.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A265 GR 1 titanium alloy strip sheet plate
The shear test, when speci? Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1?
Approved May 1, Number of Tests and Retests 8. This standard has been approved for use by agencies of the Department of Defense.
Materials and Manufacture 5. Permissible Variations Metric Equivalents in.
Ultrasonic Examination in accordance with Speci? NOTE 2—Punch marks for measuring elongation after fracture shall be made on the? Last previous edition approved in as A — If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer. Greater separation shall be cause for rejection. All other tensile test requirements of the speci? Specify whether applicable to the cladding alloy, backing steel, or both see Section General Requirements for Delivery For purposes of de?
The sides of the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1? ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures. Areas within 1 in. Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci?
Current edition approved May 1, A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci? The minimum cladding thickness for shear testing shall be 0. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
The steel shall be made by the open-hearth, electric furnace with separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer.
If the requirements of this speci? The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance. Zstm of those considered suitable for use with this speci?
The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition. The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or aa265 general structural applications.
The composite plate shall undergo shear strength test, bond strength test, and tension test and shall conform to the required tensile strength and yield strength.
When none has been speci? Each specimen shall be in the? The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The tensile properties thus determined shall meet the base steel requirements.
ASTM A GR 1 titanium alloy strip sheet plate
Chemical analysis may be accomplished by wet chemical or instrumental procedures. The base metal shall conform to the chemical requirements of the speci? Workmanship Finish, x265 Appearance